Oscilloscope, 100 MHz, 2 Trace

VERTICAL AMPLIFIERS (CH 1 and CH 2)
Sensitivity: 5mV/div to 5V/div. 1 mV/div to 1V/div (at X5 MAG)
Attenuator: 10 calibrated steps in 1-2-5 sequence. Vernier control provides fully adjustable sensitivity between steps, adjustment range 1/1 to 1/2.5 Accuracy +-3% (+-5% at X5 MAG)
Input Impedance: 1MW+ 3% Input Capacitance 25 pF +- 10pF
Frequency Response DC: DC to 100 MHz (-3 dB) on 10mV/Div setting X5 MAG DC to 20 MHz (-3 dB)
AC: 10Hz to 100 MHz (-3 dB)
Rise Time 3.5 ns (Overshoot <=5%) Signal Delay Time Variable Square Wave Characteristics Overshoot less than 5%, 10mV/div range Other ranges within 5% additional Maximum Input Voltage 400V (DC + AC peak) VERTICAL AMPLIFIERS Operating Modes CH 1, CH 2, Dual, Add Delay Time Between Channels Within 1 ns between CH 1 and CH 2 Crosstalk 30:1 at 100 kHz SWEEP SYSTEM Operating Modes A A sweep B Delayed B sweep B TRIGGERED B sweep triggered after delay A Time Base Sweep Mode Auto, normal Sweep Time: 5s to 20ns/div., 23 steps in 1-2-5 sequence with variable control Accuracy +-3% Hold Off Time Continuously variable. Adjustment range from normal to 1,5 times the sweep time B Time Base Delay Method Continuous delay. Triggered delay Sweep Time 20ns to 0.5s/div., 23 steps in 1-2-5 sequence Accuracy +-3% Hold Off Time Continuously variable. Adjustment range from normal to 1.5 times the sweep time B Time Base Delay Method Continuous delay. Triggered delay Sweep Time 20 ns. to 0.5s/div., 23 steps in 1-2-5 sequence Accuracy +-3% Delay Time Start point: 0.5 div to + 0.3 div. End point: 10 div + 1 div Delay Jitter Within 1/10,000 of full scale sweep time TRIGGERING A Trigger Source CH 1, CH 2, LINE, EXT Sensitivity 30Hz to 110 MHz TV-V 20Hz - 30kHz TV-H 3 kHz - 100 kHz Slope + or - B Trigger The A trigger is also the B trigger EXTERNAL TRIGGER Input Impedance 1 m, 30 pF Maximum Input Voltage 300V (DC + AC peak) HORIZONTAL AMPLIFIER X-Y Mode X Axis = CH 1, Y Axis = CH 2 Sensitivity 5 mV/div to 5 V/div, CH 1 and CH 2 Accuracy +- 3% calibrated position, +-6% using x10 MAG Frequency Response DC: DC to 100 MHz (-3 dB) X5 MAG DC to 20 MHz (-3 dB) AC 10 Hz to 100 MHz (-3 dB) Rise Time 3.5 ns (Overshoot <=5%) Signal Delay Time Variable Square Wave Characteristics Overshoot less than 5%, 10 mV/div range Other ranges within 5% additional Maximum Input Voltage 400V (DC + AC peak) VERTICAL AMPLIFIERS Operating Modes CH 1, CH 2, Dual, Add Delay Time Between Channels Within 1 ns between CH 1 and CH 2 Crosstalk 30:1 at 100 kHz SWEEP SYSTEM Operating Modes A A sweep B Delayed B sweep B TRIGGERED B sweep triggered after delay A Time Base Sweep Mode Auto, normal Sweep Time: 5s to 20ns/div., 23 steps in 1-2-5 sequence with variable control Accuracy +-3% Hold Off Time Continuously variable. Adjustment range from normal to 1.5 times the sweep time B Time Base Delay Method Continuous delay. Triggered delay Sweep Time 20ns. to 0.5s/div., 23 steps in 1-2-5 sequence Accuracy +-3% Delay Time Start point: 0.5 div to + 0.3 div. End point: 10 div + 1 div EXTERNAL TRIGGER Input Impedance 1 m, 30 pF Maximum Input Voltage 300V (DC + AC peak) HORIZONTAL AMPLIFIER X-Y Mode X Axis = CH 1, Y Axis = CH 2 Sensitivity 5 mV/div to 5 V/div, CH 1 and CH 2 Accuracy +-3% calibrated position, +-6% using x10 MAG Frequency Response DC to 2 MHz (-3 dB) CH I (Y) OUTPUT Output Voltage Approx. 100mV/div open circuit Approx. 50 mV/div into 50 Ω Freq. Response 50 Hz to 30 MHz Output Impedance approx. 50 CRT Type Rectangular with integral graticule Display Area 8x10 div (1 div = 1 cm) Accelerating Voltage 15 kV Phosphor P31 Scale Illumination None Trace Rotation Electrical, front panel adjustable Other Specifications Z Axis (Intensity Modulation) Sensitivity: 3V or greater, TTL level. Negative polarity increases brightness Input Impedance 15 k Usable Freq. Range DC to 3.5 MHz Maximum Input Voltage 20 V (DC + AC peak) CAL/Probe Compensation Waveform Positive going squareware Output Voltage 0.5 V p-p +- 3% Frequency Approx. 1 kHz Duty Cycle 50 +- 5% Power Requirements 100/120/220/240/VAC +- 10%, 50/60 Hz, approximately 55 W Dimensions (HxWxD) 12.76x15.68x5.2'' (324x398x132 mm) Weight 18.7 lbs. (8.5 kg) ENVIRONMENT Within Specified Accuracy 50 0 to 95 0 F (10 0 to 35 0 C), 85% maximum RH Full Operation 32 0 to 104 0 F (0 0 to +40 0C), 85% maximum RH Storage -4 0 to 158 0 F (-20 0 to +70 0 C) Accessories Three Year Warranty SUPPLIED: Instruction Manual, Two PR-37A x1/x10/Ref. Probes or equivalent, AC Power Cord, Spare Fuse OPTIONAL: PR-32A Demodulator Probe, PR-46A x10 Probe, PR-37A x1/x10/REE Probe, PR-100A x100 Probe, PR-55 High Voltage x1000 Probe, LC-210A Carrying Case